Z133 Industry Standards

StandardChapterSectionStandard TextCategoriesTags
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.3 - Working in Proximity to Electrical Hazards – Utility Line Clearance4.3.13 Branches that are contacting exposed energized conductors or equipment, or that are within the distances specified in Table 3, may be removed only through the use of insulating equipment and/or tools.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.3 - Working in Proximity to Electrical Hazards – Utility Line Clearance4.3.14 Branches and other parts of trees within the minimum approach distances (MAD) which have been browned or charred by past electrical arcing or contact, should be treated with caution. The following steps should be followed when this condition is present:
(a) Climbing of trees in such condition should be assessed by a qualified line clearance arborist and supervisor to determine whether or not an electrical hazard exists and mitigation is necessary before performing arboricultural operations.
(b) The arborist in charge shall establish a plan to safely manage the work.
(c) Work strategies, in accordance with contract employer and host utility work rules, shall be employed so that each employee of the contract employer and the host employer is protected (see Subsection 4.3.12 and Annex H, Electrical Hazard Abatement, on determining an electric hazard mitigation plan).
electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.3 - Working in Proximity to Electrical Hazards – Utility Line Clearance4.3.15 Rubber gloves, with or without leather or other protective covering, shall not be considered as providing any measure of safety from electrical hazards.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.3 - Working in Proximity to Electrical Hazards – Utility Line Clearance4.3.16 Footwear, including lineman’s overshoes or those with electrical-resistant soles, shall not be considered as providing any measure of safety from electrical hazards.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.1 - Vehicles and Mobile Equipment5.1.1 All applicable requirements in Section 3, General Safety Requirements, shall apply to this section.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.1 - Vehicles and Mobile Equipment5.1.2 Pre- and post-trip inspections shall be performed on all equipment. Inspections and operational checks shall be performed in accordance with applicable Federal Motor Carrier Safety Regulations (FMCSR), and state and local requirements.
5.1.2.1 If an inspection reveals a defect that could affect the safe operation of the equipment, the equipment shall be removed from service. To prevent operating the equipment prior to repairs, the defects shall be documented and documentation made visible for other operators. The inspection record shall not be removed until the repairs have been made and the equipment is safe to use.
SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.1 - Vehicles and Mobile Equipment5.1.3 When the operators’ view of hazards may be obstructed, walk-through inspections of the area where equipment will travel shall be performed. If hazards cannot be removed, the hazards shall be flagged, marked, or otherwise identified, and the operator shall be made aware of the hazards prior to proceeding. If a written pre-job briefing exists for the work being completed, identified hazards shall be documented.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.1 - Vehicles and Mobile Equipment5.1.4 Equipment shall be equipped and maintained with manufacturers’ safety devices, instructions, decals, and safeguards.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.1 - Vehicles and Mobile Equipment5.1.5 Manufacturers’ preventive maintenance inspections and parts replacement procedures should be followed.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.1 - Vehicles and Mobile Equipment5.1.6 No part of the body shall be used to locate or stop hydraulic leaks.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.1 - Vehicles and Mobile Equipment5.1.7 Equipment shall be inspected, operated, and maintained only by employer-authorized personnel.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.1 - Vehicles and Mobile Equipment5.1.8 Material and equipment carried on vehicles shall be properly stored and secured in compliance with the design of the equipment and in accordance with federal, state, or local regulations.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.1 - Vehicles and Mobile Equipment5.1.9 Manufacturer-provided slip/skid-resistant surfaces shall be maintained.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.1 - Vehicles and Mobile Equipment5.1.10 Safety seatbelts, when provided by the manufacturer, shall be worn by the driver and passenger(s) while the vehicle is in motion.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.2 Before the aerial device is set up for use, the worksite shall be surveyed for hazards, such as: 1. insufficient supporting surfaces, such as soft ground 2. ditches 3. excessive slopes, drop-offs, curbs, and floor obstructions 4. debris 5. overhead obstructions and electrical conductors 6. weather conditions 7. presence of unauthorized persons 8. road or worksite traffic 9. subsurface chambers, such as underground utility components or septic systemsSAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.3 Aerial devices or aerial ladders shall not be used as cranes or hoists to lift, support, or lower materials or tree parts unless they were specifically designed by the manufacturer to do so.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.4 A minimum of two wheel chocks shall be set before using an aerial device unless the device has no wheels on the ground or is designed for use without chocks.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.5 Outriggers or stabilizers shall be used if manufacturers’ instructions require their use. All outriggers shall be properly set on pads before the aerial device is moved from the boom rest (cradle).SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.6 The operator of the outrigger controls shall ensure adequate clearance exists and give warning to all workers on the worksite prior to lowering outriggers.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.7 Aerial devices shall be provided with fall protection anchor(s) meeting design requirements of the ANSI/SIA A92.2 standard on which to secure an approved system of personal fall protection which shall be worn by the operator(s) whenever aloft.
5.2.7.1 All fall protection shall be worn and adjusted in accordance with manufacturer specification.
5.2.7.2 The carabiners and snap hooks used as part of a fall-arrest system shall have a 3,600 pound rated gate. Carabiners and snap hooks shall not be linked together unless designed to do so and accepted by the manufacturer.
SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.8 Combined loads shall not exceed rated lift capacities. Load ratings shall be permanently posted on aerial devices in accordance with ANSI/SIA A92.2 or A92.5, as applicable to the specific aerial device.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.9 Aerial buckets/platforms shall not have more occupants or load than allowed by the manufacturer’s rating.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.10 The operator shall stand firmly on the floor of the platform (aerial bucket) and shall not use railings, planks, ladders, or any other device in or on the bucket for achieving additional working height.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.11 Climbing spurs (gaffs) shall not be worn while working from an aerial device.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.12 A sheath or scabbard shall be utilized in the bucket to cover sharp-edged tools, such as chain saws and hand saws (unless of the folding type that covers the cutting teeth when closed), while stored for use.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.13 During pruning/removal operations, a hand saw shall be taken by the aerial device operator while working aloft.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.14 Before moving an aerial device for travel, the operator shall inspect the aerial device to ensure the boom(s) are cradled and secured, the tools are secured, and the outriggers are stowed or positioned for travel per manufacturer specifications.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.15 When operating an aerial device, the operator shall look primarily in the direction the platform (aerial bucket) is traveling and be aware of the location of the booms, including the elbow/knuckle area, in relation to all other objects and hazards.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.16 When transferring from the platform (aerial bucket) of an aerial device to a tree in order to complete an arboricultural operation, arborists shall remain secured to the aerial device until they are properly secured to the tree. At no time shall work be performed while an arborist is secured to both the aerial device and the tree.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.17 Arborists shall remain properly secured at all times when transferring from the bucket of an inoperative aerial device to the platform (aerial bucket) of an operative aerial device to facilitate an emergency descent.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.18 The lower controls of an aerial device shall not be used for continuous operation when the operator is in the platform (aerial bucket).
5.2.18.1 Lower controls shall not be operated unless permission has been obtained from the arborist in the platform, except in case of emergency.
SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.19 Clearances from passing vehicles shall be maintained or traffic control shall be provided when booms or platforms (aerial buckets) are operated over roads in accordance with the Manual on Uniform Traffic Control Devices (MUTCD), Part 6, federal, state, or local, as applicable.
5.2.19.1 Clearances shall be maintained for outriggers and any other portion of the vehicle that may extend into or over the lanes of travel or that work over them.
SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.20 Workers shall not perform arboricultural operations work, such as pruning or cutting of trees, from the top of vehicle bodies or cab protectors unless the worker is properly protected from the fall hazard.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.21 Hydraulic/pneumatic tools shall be disconnected when they are being serviced or adjusted, except where manufacturers’ procedures require otherwise.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.22 To avoid flying particles or whipping hydraulic/pneumatic hoses, pressure shall be released before connections are broken, except where quick-acting connectors are used. Hydraulic/pneumatic hoses shall never be kinked in order to cut off pressure.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.23 No part of the body shall be used to locate or stop hydraulic leaks.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.24 Hoses affecting dielectric characteristics of equipment shall meet manufacturers’ requirements.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.25 The flash point of hydraulic fluid shall meet the requirements set by the manufacturer.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.26 Booms, platforms (aerial buckets), or any other part of the aerial device shall not be allowed to make contact or violate minimum approach distances with energized electrical conductors, poles, or similar conductive objects.
5.2.26.1 Due to hazards of step and touch potential, if the distance between the aerial device and energized conductor(s) is unintentionally less than the required minimum approach distance (MAD), workers on the ground shall move away and remain clear of the aerial-device vehicle and attached equipment (e.g., chipper) until the required MAD is reestablished.
SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.27 Aerial devices equipped with an elevating structure that raises the turret and booms and changes the reach of the device’s uninsulated portions shall be operated so that no portion of the aerial device and its elevating structure violate the minimum approach distance (MAD) from energized electrical lines as specified in this standard. A spotter(s) shall be used when the aerial lift is working close to MAD and potentially could violate MAD.
5.2.27.1 When the minimum approach distance (MAD) is likely to be violated, the spotter(s) shall warn the equipment operator and other ground personnel, if present, and direct ground personnel to keep clear of the vehicle and attachments until MAD is visually established and communicated.
SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.28 Electric cables/cords used with electric saws, lights, or other conductive material shall not be run from the vehicle to the platform (aerial bucket) when arborists are working in proximity to energized electrical conductors.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.29 (a) Platforms (aerial buckets) on insulated aerial devices shall have no through- cracks or holes below the lip of the platform.
(b) Insulating liners shall have no holes below the lip of the liner or vertical cracks greater than 6 inches (15.24 cm) long.
SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.30 During aerial device operations, arborists and other workers shall maintain a minimum approach distance from energized electric conductors in accordance with the appropriate table of this standard as required by their level of training.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.31 Arborists and other workers shall be instructed that insulated aerial platforms (aerial buckets) do not protect them from other electric paths to the ground, such as paths through trees or guy wires or from phase-to-phase contact. Either form of electric contact can be fatal.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.32 Arborists using a boom-supported elevating work platform shall operate the platform within the limits of intended use as defined by the manufacturer in the operator’s manual, ANSI/SIA A92.5, and applicable governmental regulations.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.33 Only operators who have received instruction and training regarding the inspection, application, responsibilities, and operation shall operate a boom-supported elevating work platform. The operator shall be informed of the location of the manual and familiarized with the controls, safety devices, and operating characteristics of the work platform being operated.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.34 Insulated boom-supported elevating work platforms shall meet the electric safety requirements of ANSI/SIA A92.2.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.35 The operator shall assess the worksite hazards present that pertain to the use of a boom- supported elevating work platform on that worksite. The operator and other workers shall develop, communicate, and implement a work plan to mitigate the hazards identified on that worksite.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.3 - Brush Chippers5.3.1 The items contained in Section 5.1, Vehicles and Mobile Equipment, shall always be included in the review of this section.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.3 - Brush Chippers5.3.2 Access panels and guards for maintenance and adjustment, including the discharge chute and cutter housing, shall be closed and secured prior to starting the engine of brush chippers. These access panels shall not be opened or unsecured until the engine and all moving parts have come to a complete stop and the ignition key removed and pocketed (see Annex C.2, Control of Hazardous Energy).SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.3 - Brush Chippers5.3.3 Rotary drum or disc brush chippers not equipped with a mechanical infeed system shall be equipped with an infeed hopper not less than 85 inches (2.15 m) measured from the blades or knives to ground level over the center line of the hopper. Chippers with a mechanical infeed system shall also have a hopper not less than 85 inches (2.15 m) measured from the pinch point of the feeder wheels to ground level over the center line of the hopper. Side members of the infeed hopper shall have sufficient height so as to prevent workers from contacting the blades or knives during operations.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.3 - Brush Chippers5.3.4 Rotary drum or disc brush chippers not equipped with a mechanical infeed system shall have a flexible anti-kickback device installed in the infeed hopper to reduce the risk of injury from flying chips and debris.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.3 - Brush Chippers5.3.5 Chippers equipped with a mechanical infeed system shall have a quick-stop and reversing device on the infeed system. The activating mechanism for the quick-stop and reversing device shall be located across the top, along each side, and close to the feed end of the infeed hopper within easy reach of the worker.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.3 - Brush Chippers5.3.6 Vision, hearing, and other appropriate personal protective equipment shall be worn when in proximity of an operating brush chipper, in accordance with Section 3.3, Personal Protective Equipment (PPE), and as defined by the Personal Protective Equipment Hazard Certification.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.3 - Brush Chippers5.3.7 Arborists, mechanics, and other workers shall not reach beyond the plane of the infeed hopper when the cutter disc, rotary drum, or feed rollers are moving. If maintenance is needed, all moving parts shall come to a complete stop and keys shall be removed from the ignition and pocketed by the authorized person before proceeding. See Annex C.2, Control of Hazardous Energy.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.3 - Brush Chippers5.3.8 For additional requirements, see Section 8.7, Brush Removal and Chipping.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.4 - Sprayers and Related Equipment5.4.1 The items contained in Section 5.1, Vehicles and Mobile Equipment, shall always be included in the review of this section.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.4 - Sprayers and Related Equipment5.4.2 Working and walking surfaces of all sprayers and related equipment shall be covered with skid-resistant material.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.4 - Sprayers and Related Equipment5.4.3 Equipment on which the applicator/operator stands while the vehicle is in motion shall be equipped with guardrails around the working area. Guardrails shall be constructed in accordance with ANSI A1264.1.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.4 - Sprayers and Related Equipment5.4.4 All fittings and hoses shall be of sufficient strength to withstand or exceed the maximum pressure of the system. At no time should any part of the body be used to locate leaks or damaged sections of hose.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.4 - Sprayers and Related Equipment5.4.5 The operator shall be aware of the location and use of all safety shut-off valves.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.4 - Sprayers and Related Equipment5.4.6 All tanks shall have means to determine the level of liquid in the tanks without opening the tank lid.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.4 - Sprayers and Related Equipment5.4.7 The applicator/operator shall make a visual inspection of hoses, fittings, exposed plumbing, tanks, covers, and related equipment prior to its use each workday.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.4 - Sprayers and Related Equipment5.4.8 The applicator/operator shall not allow hoses or other parts of the equipment to create a tripping hazard for coworkers or the public.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.4 - Sprayers and Related Equipment5.4.9 The applicator/operator shall have a firm grip on the spray gun/excavation tool when pulling the trigger.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.4 - Sprayers and Related Equipment5.4.10 Entering enclosed tanks or spaces shall be prohibited unless performed through a confined-space entry plan in compliance with OSHA 1910.146 requirements, which include atmospheric quality testing, training, personal protective equipment, supervision, and emergency response procedures.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.4 - Sprayers and Related Equipment5.4.11 Related equipment
5.4.11.1 The applicator/operator shall be aware of underground utility locations when drilling holes in the ground for fertilizer or pesticide applications. All underground utility locations shall be determined by calling the ‘Call before you Dig’ national telephone number 811.
5.4.11.2 The equipment shall have splashguards, and the applicator shall wear eye protection when injecting liquid fertilizer or pesticides into the ground.
5.4.11.3 The applicator shall wear eye protection and follow label instructions when injecting liquids into trees.
SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.5 - Stump Grinders5.5.1 The items contained in Section 5.1, Vehicles and Mobile Equipment, shall always be included in the review of this section.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.5 - Stump Grinders5.5.2 Stump grinders shall be equipped with enclosures or guards that reduce the risk of injury during operation. Enclosures and guards shall be kept in place when the grinding wheels are rotating or cutting.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.5 - Stump Grinders5.5.3 Arborists and other workers at the stump-grinding worksite shall wear eye, hearing, and other personal protective equipment in accordance with Section 3.3, Personal Protective Equipment (PPE).SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.5 - Stump Grinders5.5.4 The operator shall be aware of underground utility locations, per Subsection 3.4.2, prior to performing work. All work shall be in compliance with federal, state, and local underground facility protection laws (e.g., Dig-Safe or One-call Underground Facility Locator programs).SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.5 - Stump Grinders5.5.5 The operator shall ensure that all other persons remain clear of the stump grinder while the cutting wheel is engaged, rotating, or grinding.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.5 - Stump Grinders5.5.6 The operator shall ensure no secondary activities take place with the stump grinder, such as using the backfill blade, while the cutting wheel is engaged, rotating, or cutting.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.5 - Stump Grinders5.5.7 Where equipment has no remote control capabilities, the operator shall stay at the controls during the operation of the stump grinder until the cutting wheel has stopped.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.5 - Stump Grinders5.5.8 On equipment with remote controls, the operator shall remain a safe working distance as established by the employer or manufacturer, and clear of the materials being discharged and the cutting wheel while it is engaged, rotating, or grinding.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.5 - Stump Grinders5.5.9 On equipment with tethered remote controls, the operator shall ensure that the operator and tether remain clear of the cutting wheel while it is engaged, rotating, or grinding.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.5 - Stump Grinders5.5.10 Before leaving the machine unattended, the operator shall ensure that all moving parts have stopped and the key is removed and pocketed. When there is no keyed ignition system, the employer’s procedures for securing the equipment shall be followed.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.5 - Stump Grinders5.5.11 The operator shall ensure that the grinding wheel is disengaged and has stopped rotating prior to driving or moving the equipment.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.5 - Stump Grinders5.5.12 Only employer-authorized personnel shall be permitted to perform maintenance. See Annex C.2, Control of Hazardous Energy.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.5 - Stump Grinders5.5.13 When not in use, keys shall be removed and pocketed by the authorized person in charge. When there is no keyed ignition system, the employer’s procedures for securing the equipment shall be followed.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.6 - Vehicles5.6.1 The items contained in Section 5.1, Vehicles and Mobile Equipment, shall always be included in the review of this section.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.6 - Vehicles5.6.2 Regulated vehicles (those in excess of 10,000 pounds gross vehicle weight rating, or gross combined vehicle weight rating) shall be operated in compliance with the Federal Motor Carrier Safety Regulations (FMCSR), state, and local laws.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.6 - Vehicles5.6.3 A steel bulkhead or equivalent protective device shall be provided to protect workers from load shifts in vehicles carrying logs or other material.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.6 - Vehicles5.6.4 Load securement procedures shall be followed to prevent accidental shifting or discharge of logs or other materials from the vehicle during transport.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.6 - Vehicles5.6.5 Logs or other material shall not overhang the sides; obscure taillights, brake lights, or vision; or exceed height limits per state and local requirements for bridges, overpasses, utility lines, or other overhead hazards.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.6 - Vehicles5.6.6 To avoid the hazard of spontaneous combustion, wood chips should not be left in vehicles for extended periods.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.7 - Cranes and Knucklebooms5.7.1 The items contained in Section 5.1, Vehicles and Mobile Equipment, shall always be included in the review of this section.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.7 - Cranes and Knucklebooms5.7.2 Cranes shall be inspected in accordance with ASME B30.5 or ASME B30.22 (articulating boom) standards and manufacturers’ guidelines. Rigging equipment shall be inspected before each use in accordance with OSHA 1910.184 and manufacturers’ guidelines.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.7 - Cranes and Knucklebooms5.7.3 Operators of hoisting equipment shall be trained and shall maintain a 10-foot (3.05-m) minimum approach distance from unguarded, overhead energized conductors, or greater separation in accordance with Table 1 of this standard. A spotter shall be used when work is being performed that could encroach on minimum approach distances from energized conductors. The spotter shall be positioned to effectively gauge the clearance distance and give timely information to the qualified crane operator.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.7 - Cranes and Knucklebooms5.7.4 Only a qualified crane operator shall be used.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.7 - Cranes and Knucklebooms5.7.5 Cranes shall be equipped to comply with the design standards published in ASME B30.5 or ASME B30.22 (for articulating booms).SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.7 - Cranes and Knucklebooms5.7.6 Hooks on overhaul ball assemblies, lower load blocks, or other attachment assemblies shall be of a type that can be closed and locked, eliminating the hook throat opening.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.7 - Cranes and Knucklebooms5.7.7 Crane operators shall remain at the controls while a load is suspended.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.7 - Cranes and Knucklebooms5.7.8 Tree sections shall be rigged to minimize load shifting. Controlled load lowering shall be used. Shock-loading shall be avoided, and free fall is prohibited.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.7 - Cranes and Knucklebooms5.7.9 The qualified crane operator and the arborist in charge shall meet prior to the work to review procedures to be followed. If the work involves a spotter/signal person and/or an additional qualified arborist being hoisted by the crane, these persons shall participate in the review as well. A job briefing shall be done before any work begins in accordance with Subsection 3.4.3.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.7 - Cranes and Knucklebooms5.7.10 Cranes shall be set up in accordance with manufacturers’ specifications.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.7 - Cranes and Knucklebooms5.7.11 A qualified arborist may be hoisted into position utilizing a crane if he/she is tied in with an arborist climbing line and arborist saddle and secured to an anchor point on or above the crane hook or to the crane boom. The following procedures shall be followed when a qualified arborist is to be hoisted by a crane:
5.7.11.1 Only a qualified arborist shall authorize the use of a crane for hoisting a qualified arborist into position when he/she has determined that it is the safest and/or only feasible method to perform the work or to gain access to a tree.
5.7.11.2 The arborist climbing line shall be secured to the crane in such a way that it does not interfere with the function of any of the crane’s components.
5.7.11.2.1 No part of the crane shall be allowed to compromise the climbing line or any component of the climbing system.
5.7.11.2.2 The qualified arborist shall use a second point of attachment on or above the crane hook or to the crane boom while being hoisted into position in the tree.
5.7.11.3 Continuous communication between the crane operator and the qualified arborist being hoisted shall be maintained, either directly or through a spotter/ signal person, using two-way radio, vocal communication, or accepted hand signals (see Annex G, Hand Signal Chart for Crane Operations).
5.7.11.4 The qualified crane operator shall remain at the controls while the qualified arborist is attached to the crane.
5.7.11.5 When the qualified arborist is being hoisted, hoisting speed shall not exceed 100 feet/minute (0.5 m/sec). During hoisting operations, there shall be no sudden acceleration or deceleration of the moving load.
5.7.11.6 Controlled load lowering is required and free fall of the load line hoist is prohibited if an employee is being hoisted.
5.7.11.7 The crane carrier shall not travel at any time while a qualified arborist is attached.
5.7.11.8 An accurate estimation of the load radius to be used during lifting shall be made before a qualified arborist is hoisted.
5.7.11.9 The qualified arborist shall be detached from the crane any time a load is suspended.
EXCEPTION to 5.7.11.9: When it has been determined that all reasonably possible alternate methods are inaccessible and attachment to the subject tree would create a greater safety risk due to its hazardous condition, the qualified crane operator and the qualified arborist shall allow the qualified arborist to remain attached to the crane while a load is suspended. Possible alternate methods include, but are not limited to
(a) the qualified arborist securing to the tree and detaching from the crane before it comes under load;
(b) using a second crane;
(c) using an aerial lift device;
or (d) using an adjacent tree.
5.7.11.9.1 When the qualified arborist is attached to the crane with a suspended load, the total weight shall not exceed 50 percent of the load capacity for the radius and configuration of the crane.
5.7.11.9.2 The qualified arborist shall descend to the ground as soon as he/she has determined that the piece is detached from the tree and that it is safe to do so.
SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.7 - Cranes and Knucklebooms5.7.12 The qualified arborist shall estimate the weight of the tree section to be suspended prior to cutting the section. The load weight estimate shall be communicated to the crane operator. After the pick is complete, the crane operator should verify, compare, and communicate the estimated weight to the qualified arborist. A green log weight chart (as shown in Annex E, Weight of Green Logs) shall be available to the crew. The suspended load should not exceed 75 percent of the load chart capacity of the crane.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.7 - Cranes and Knucklebooms5.7.13 Radio communication between the qualified arborist and qualified crane operator shall be used during blind picks. Radio communication shall be hands-free.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.8 - Specialized Units5.8.1 The items contained in Section 5.1, Vehicles and Mobile Equipment, shall always be included in the review of this section.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.8 - Specialized Units5.8.2 Off-road and tracked vehicles shall be operated according to the operating environment and the manufacturer’s instructions and guidelines.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.8 - Specialized Units5.8.3 Towing equipment for brush hogs and similar implements should be equipped with a deadman control. When deadman controls are not available, the worker shall disengage the power source to the rotary or cutter head before dismounting.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.9 - Equipment-Mounted Winches5.9.1 The items contained in Section 5.1, Vehicles and Mobile Equipment, shall always be included in the review of this section.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.9 - Equipment-Mounted Winches5.9.2 Each day before being used, the winch line and all fastenings and attachments shall be inspected for damage or defects by a qualified person. Additional inspections shall be performed during winch line use, where service conditions warrant. Damaged or defective winch lines shall be immediately removed from service.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.9 - Equipment-Mounted Winches5.9.3 Winch line hooks and attachment points shall be inspected for damage. Damaged hooks or attachment assemblies shall be taken out of service.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.9 - Equipment-Mounted Winches5.9.4 All mounting bolts and hardware shall be inspected for loose or missing components. The winch shall not be used until complete repairs are made to damaged or missing bolts and hardware.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.1 - General7.1.3 Hand tools and equipment that have been made unsafe by damage or defect, including tools with loose or cracked heads or cracked, splintered, or weakened handles, shall not be used.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.1 - General7.1.4 Workers shall maintain a safe working distance from other workers when using hand tools and equipment.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.1 - General7.1.5 When climbing into a tree, arborists shall not carry hand tools and equipment in their hands unless the tools are used to assist them in climbing. Tools other than ropes or throwlines shall not be thrown into a tree or between workers aloft.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.1 - General7.1.6 Arborist climbing lines or handlines (line, handline) may be used for raising and lowering hand tools and equipment. Arborists should raise or lower hand tools and equipment in a manner such that the cutting edge will not contact the arborist climbing line or handline.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.1 - General7.1.7 Hand tools and equipment shall be properly stored or placed in plain sight out of the immediate worksite when not in use.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.2 - Cant Hooks, Cant Dogs, Peaveys, and Tongs7.2.1 The items contained in Section 7.1, General, shall always be included in the review of this section.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.2 - Cant Hooks, Cant Dogs, Peaveys, and Tongs7.2.2 Cant hooks, cant dogs, peaveys, and tongs should be firmly set before applying force.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.2 - Cant Hooks, Cant Dogs, Peaveys, and Tongs7.2.3 Points of hooks shall be at least 2 inches (5 cm) long and kept sharp.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.2 - Cant Hooks, Cant Dogs, Peaveys, and Tongs7.2.4 Arborists and other workers shall always stand uphill from rolling logs, and all workers shall be warned and in the clear before logs are moved.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.3 - Wedges, Chisels, and Gouges7.3.1 The items contained in Section 7.1, General, shall always be included in the review of this section.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.3 - Wedges, Chisels, and Gouges7.3.2 Wedges, chisels, and gouges shall be inspected for cracks and flaws before use. Tools with damaged heads shall not be used.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.3 - Wedges, Chisels, and Gouges7.3.3 Wedges and chisels shall be properly pointed and tempered.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.3 - Wedges, Chisels, and Gouges7.3.4 Eye protection shall be used during impact operations.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.3 - Wedges, Chisels, and Gouges7.3.5 Only wood, plastic, or soft-metal wedges shall be used while operating chain saws.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.3 - Wedges, Chisels, and Gouges7.3.6 Wood-handled chisels should be protected with a ferrule on the striking end.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.3 - Wedges, Chisels, and Gouges7.3.7 Wood, rubber, or high-impact plastic mauls, sledges, or hammers should be used when striking wood-handled chisels or gouges.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.4 - Chopping Tools7.4.1 The items contained in Section 7.1, General, shall always be included in the review of this section.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.4 - Chopping Tools7.4.2 Chopping tools should not be used while working aloft.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.4 - Chopping Tools7.4.3 Chopping tools shall not be used as wedges or used to drive metal wedges.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.4 - Chopping Tools7.4.4 Chopping tools shall be swung away from the feet, legs, and body, using the minimum force practical for function and control.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.4 - Chopping Tools7.4.5 When swinging tools such as grub hoes, mattocks, and axes, a secure grip, firm footing, and clearance of workers and overhead hazards shall be maintained.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.5 - Ladders7.5.1 The items contained in Section 7.1, General, shall always be included in the review of this section.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.5 - Ladders7.5.2 Ladders made of metal or other conductive material shall not be used where electrical hazards exist. Only wooden ladders (constructed in accordance with ANSI A14.1) or nonconductive ladders made of synthetic material equal to or exceeding the strength of wooden ladders shall be used.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.5 - Ladders7.5.3 Metal ladders used where no electrical hazard exists shall conform to ANSI A14.2.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.2 - Ropes and Arborist Equipment8.2.5 Arborist climbing lines used for stationary rope systems shall conform to the diameter, construction, strength, and elongation standards of Subsection 8.2.4 and shall be compatible with the components used in the stationary rope system.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.2 - Ropes and Arborist Equipment8.2.6 Prusik loops, split-tails, doubled-hitch cords, and work-positioning lanyards used in a climbing system shall meet the minimum breaking strength of 5,400 pounds.
8.2.6.1 Hitch cords, Prusik loops, and split-tails shall be manufactured from material(s) suitably resistant to the abrasion and temperatures experienced during work and rescue scenarios.
tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.2 - Ropes and Arborist Equipment8.2.7 Snap hooks (rope snaps) used as part of a climber’s work positioning (suspension) system shall be self-closing and self-locking, with a minimum tensile strength of 5,000 pounds (22.24 kN).tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.2 - Ropes and Arborist Equipment8.2.8 Carabiners used as part of a climber’s work-positioning (suspension) system shall be self- closing and self-double locking and shall have a gate-locking mechanism that requires at least two consecutive, deliberate actions to unlock. A carabiner shall be capable of withstanding a 5,000 pound (22.24 kN) load along its major axis with the gate closed without breaking or distortion sufficient to release the gate.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.2 - Ropes and Arborist Equipment8.2.9 Carabiners and snap hooks used as part of a climber’s fall protection (work positioning/suspension/fall arrest system) shall not be linked together unless designed to do so and accepted by the manufacturer.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.2 - Ropes and Arborist Equipment8.2.10 Load-rated screw links used as part of a climber’s work positioning (suspension) system shall have a tensile strength of 5,000 pounds (22.24 kN) and shall be securely tightened to ensure they will not unintentionally open during use.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.2 - Ropes and Arborist Equipment8.2.11 Splicing shall be done in accordance with manufacturers’ specifications.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.2 - Ropes and Arborist Equipment8.2.12 Equipment used to secure an arborist in a tree or to an aerial device shall not be used for anything other than its intended purpose. EXCEPTION: An arborist’s climbing line may be used to raise and lower lightweight tools and equipment such as chainsaws, hand tools, and additional lines.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.2 - Ropes and Arborist Equipment8.2.13 Rope ends shall be finished in a manner to prevent raveling.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.2 - Ropes and Arborist Equipment8.2.14 Ropes and climbing equipment shall be stored and transported in such a manner to prevent damage through contact with sharp tools, cutting edges, gas, oil, or chemicals.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.2 - Ropes and Arborist Equipment8.2.15 Arborist climbing lines shall never be left in trees unattended.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.2 - Ropes and Arborist Equipment8.2.16 Climbing spurs shall have gaffs of the type and length suitable for the tree being climbed. Manufacturers’ recommendations for inspection, maintenance, sharpening, and replacing worn gaffs shall be followed.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.2 - Ropes and Arborist Equipment8.2.17 The non-working end of any work-positioning lanyard shall have a fixed termination such as a fixed stopper knot, eye splice, snap, carabiner, or other hardware that does not permit the non-working end of the lanyard to advance through the friction device, or it shall be securely connected to a rated connection point on the climbing saddle.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.3 - Pruning and Trimming8.3.1 Pruning should be conducted in accordance with the ANSI A300 (Part 1) standard.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.3 - Pruning and Trimming8.3.2 The arborist in charge shall establish a safe work plan to manage the drop zone. Communications among arborists aloft and other workers on the ground shall be established before cutting and dropping limbs. The command “stand clear” from aloft and the response “all clear” from the ground are terms that may be used for this purpose. Pre- arranged, two-way hand signals may also be used. Arborists and other workers returning to the drop zone shall be acknowledged by arborists aloft.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.3 - Pruning and Trimming8.3.3 Pole pruners and pole saws, when hung, shall be securely positioned to prevent dislodgment. Pole pruners or pole saws shall not be hung on electrical conductors or left in a tree unattended. Pole saws and pole pruners shall be hung so that sharp edges are away from the arborist and shall be removed when the arborist leaves the tree.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.3 - Pruning and Trimming8.3.4 Scabbards or sheaths shall be used to carry hand saws. Folding hand saws, when not in use, shall be stowed in a manner that protects the worker and others from the cutting edge.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.3 - Pruning and Trimming8.3.5 Pole tools used in proximity to energized conductors shall be constructed with fiberglass- reinforced plastic (FRP) or wooden poles meeting the requirements of OSHA 1910.269(r)(1)(iv).tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.3 - Pruning and Trimming8.3.6 Limbs that cannot be safely controlled by hand or free-dropped shall have a separate rigging line attached to them to help control their fall. Rigging practices shall conform to the requirements in Section 8.5, Rigging, of this standard.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.3 - Pruning and Trimming8.3.7 Dry conditions and dead palm fronds present an extreme fire hazard. When dry conditions exist, arborists and other workers shall not smoke while working in or near dead palm fronds. All chain saws used under such conditions shall have mufflers and spark arresters in good working condition.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.3 - Pruning and Trimming8.3.8 Palm frond skirts shall be removed from the top down. Arborists performing this work while climbing shall be supported by an arborist climbing system, and when possible, positioned above the skirt. Arborists should not remove palm skirts by positioning themselves below the frond skirt or between the palm skirt and the trunk of the tree.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.3 - Pruning and Trimming8.3.9 Cut branches, tools, and equipment shall be removed from trees upon completion of work.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.4 - Cabling8.4.1 Cabling should be conducted in accordance with the ANSI A300 (Part 3) standard.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.4 - Cabling8.4.2 Arborists and other workers on the ground shall not stand in the drop zone when a cabling system is being installed.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.4 - Cabling8.4.3 Tools used for cabling shall be carried in a bag, placed on a belt designed to hold such tools, or securely attached to a lanyard (tool lanyard) to prevent the tools from falling.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.4 - Cabling8.4.4 When installing or replacing a support system, the load shall be released onto the new support system in a slow and controlled manner to help prevent sudden or dynamic loading.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.4 - Cabling8.4.5 When a previously installed support system is to be removed or replaced, it shall not be removed until a new support system is installed to take the weight off of the previously installed system, or until a temporary support system has been installed to slacken the previously installed system.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.5 - Rigging8.5.1 Arborists performing rigging operations shall inspect trees for their integrity to determine whether the trees have any visible defect that could affect the operation. If it is determined that the tree poses a risk of failure due to the forces and strains that will be created by the design of the rigging operation, an alternate plan shall be used.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.5 - Rigging8.5.2 Rigging points shall be assessed for their structural integrity by a qualified arborist. The work plan and the tree shall be considered relative to the forces being applied to any part of the tree, including branch attachments and anchoring roots, before a rigging point is chosen and established.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.5 - Rigging8.5.3 Arborists performing rigging operations shall be trained to estimate the potential forces at any point in the rigging system being used. The system components shall comply with working-load limits relative to the operation and the maximum potential forces.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.5 - Rigging8.5.4 Careful consideration shall be given to the potential for additional forces resulting from the influences of rigging design, rope angles, and the number of lines and/or line parts that will act on any rigging or anchor point.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.5 - Rigging8.5.5 A qualified arborist shall ensure that load ratings shown on the rigging equipment or provided by the manufacturer for all ropes, connecting links, and rigging equipment are observed in all rigging operations. Rigging equipment shall be chosen for the specific task based on working-load limits and design specifications. If a carabiner is used in a rigging system, loading of the gate and/or the minor axis of the carabiner shall be prevented.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.5 - Rigging8.5.6 The number of connecting links used for connecting components of a rigging system shall be minimized when possible. Arborists shall ensure that shackles, screw links, and other connecting links interface properly and are in compliance with manufacturers’ recommendations.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.5 - Rigging8.5.7 All equipment used for rigging operations shall be in good working condition. Rigging equipment and its connecting links shall be inspected immediately before use and removed from service if found to be defective, damaged, or overloaded.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.5 - Rigging8.5.8 When the potential exists for rigging equipment to be confused with climbing equipment, the equipment shall be clearly marked to indicate its different purposes.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.5 - Rigging8.5.9 When establishing a rigging point horizontally distant from the parent limb or main tree stem, the arborist should consider the need to provide additional support to help disperse the force of the proposed rigged load. Options may include: Use of a backstay to support the load-bearing rigging point by placing an appropriately rated rope from the limb used as the load-bearing rigging point back to a higher point on the main trunk of the tree or other higher and suitable limb; or Installation of an additional and separate rigging system that utilizes supporting members, other than those already in use by the primary lowering point, in an effort to have both rigging systems share the load force.
"
tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.5 - Rigging8.5.10 Workers aloft (either climbing the tree or from an aerial device) shall establish a communication system with arborists and other workers on the ground.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.5 - Rigging8.5.11 A method of verbal, audible, or visual communication shall be discussed and established during the job briefing prior to the start of removal or rigging operations. The verbal, audible, or visual communication system shall use an established command and response system (see example) or pre-arranged, two-way hand signals. The communication method shall be clearly understood and used during all rigging operations. Example ~ Command: "Stand Clear!" Response: "Clear!", "Underneath!", or "Stop!"tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.5 - Rigging8.5.12 A drop zone shall be established prior to the start of rigging operations. Workers shall stay out of the drop zone until it has been communicated by a qualified arborist, a qualified arborist trainee, or the worker aloft directly involved in the rigging operation that it is safe to enter.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.5 - Rigging8.5.13 Only qualified arborists or qualified arborist trainees directly involved in the operation shall be permitted in the drop zone when a load is being suspended by the rigging system.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.5 - Rigging8.5.14 Taglines (line, tagline) or other means may be used to help control and handle suspended loads.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.5 - Rigging8.5.15 Ground workers involved in handling rigging lines shall not be underneath moving or suspended loads and should be out of the drop zone when practical.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.5 - Rigging8.5.16 Workers aloft shall position themselves above or to the side of the piece being rigged and out of the path of movement of the piece and attached rigging when the piece has been cut. Climbers shall have a retreat/escape plan prepared.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.5 - Rigging8.5.17 Climbers and their climbing systems shall not make contact with moving or swinging parts of the rigging system when making a release cut or when the load is moving. Rigging systems shall not compromise any part of the climbing system.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.5 - Rigging8.5.18 Steps shall be taken to prevent spars from splitting or tearing during the rigging operation, and climbers shall take steps to avoid trapping, pinning, or entangling themselves in the system should the tree split or the rigging fail. Load binders are one possible means of preventing splitting.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.5 - Rigging8.5.19 A hand saw shall be with a worker aloft to make or finish cuts.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.6 - Tree Removal8.6.1 Before beginning any tree removal operation, the chain saw operator and/or crew leader shall carefully consider relevant factors pertaining to the tree and site and shall take appropriate actions to ensure a safe removal operation. Factors to include may be, but are not limited to, tree decay, tree lean, and wind (see Annex C.3, Manual Tree Felling Procedure, for a more inclusive list).tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.6 - Tree Removal8.6.2 The crew leader shall assess the number of workers necessary for the tree removal operations, develop a tree removal work plan, and communicate the work plan and job task assignments in a job briefing with the crew prior to beginning the tree removal work. In addition, a method of verbal, audible, or visual communication as set forth in Subsection 8.5.11 shall be discussed and established during the job briefing prior to the start of tree removal operations.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.6 - Tree Removal8.6.3 A drop zone shall be established prior to the start of piecing-down tree removal operations. Workers shall stay out of the drop zone until it has been communicated by a qualified arborist, a qualified arborist trainee, or the worker aloft directly involved in the piecing-down tree removal operation that it is safe to enter.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.6 - Tree Removal8.6.4 In manual tree felling operations, non-involved workers shall be positioned at a distance from the tree at least two (2.0) times the height of the tree or trunk being removed until the chain saw operator and/or crew leader communicates that it is safe to approach more closely. Involved workers other than the chain saw operator, including but not limited to those who handle ropes/taglines, come-alongs/winches, etc., shall be positioned at a distance from the tree at least one-and-one-half (1.5) times the height of the tree or trunk being removed until the chain saw operator and/or crew leader communicates that it is safe to approach more closely.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.6 - Tree Removal8.6.5 A planned retreat/escape path for all workers involved in the tree removal operation shall be prepared before piecing down tree parts or manual tree felling.
8.6.5.1 During manual tree felling, the preferred retreat/escape path for the chain saw operator is 45 degrees on either side of a line drawn opposite the intended direction of the fall.
8.6.5.2 To the extent practical, the retreat/escape path shall be cleared of obstructions and objects that would hinder retreat.
8.6.5.3 The chain saw operator shall use this path for egress once the felling cuts have been completed or the tree begins to fall.
8.6.5.4 Other involved workers shall have and use retreat/escape paths that do not hinder other retreating workers or expose any involved workers to increased hazard.
tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.6 - Tree Removal8.6.6 When it is necessary to use rigging to shorten or remove branches or to block down pieces of the tree, the qualified arborist shall consider whether the tree can withstand the strain of the lowering procedures. If the qualified arborist determines that the tree cannot withstand the strain of the lowering procedures, other means of removing the tree shall be implemented.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.6 - Tree Removal8.6.7 A rope should be attached to all trees and stems greater than 5 inches (12.7 cm) in diameter at breast height (dbh) being felled to provide stabilization and/or directional pull where assisted directional felling is required.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.6 - Tree Removal8.6.8 When there is a risk of damage to property from a tree piece or tree falling in an unintended direction, rope(s), block and tackle, come-alongs/winches, wire cable (except where an electrical hazard exists), or other appropriate devices shall be used to control the direction of fall.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.6 - Tree Removal8.6.8.1 Loaders, skid steers, or other heavy equipment shall not be used to push over trees that are being manually felled while any worker is within 1-1/2 times the height of the tree being felled. The heavy equipment being utilized shall be of the appropriate size for the task and shall offer appropriate protection for the operator.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.6 - Tree Removal8.6.9 Wedges should be used when determined to be necessary to prevent binding of the guide bar or chain when felling trees or stems. Wedges may be used as an aid in directional tree felling.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.6 - Tree Removal8.6.10 All equipment used for tree removal operations shall be in good working condition. Tree removal equipment and its connecting links shall be inspected immediately before use and removed from service if found to be defective, damaged, or overloaded.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.6 - Tree Removal8.6.11 Tree limbs shall be removed to a height and width sufficient to allow the tree parts or tree to fall clear of hazards, such as utility wires and/or other objects in the vicinity.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.6 - Tree Removal8.6.12 During manual tree felling operations, notches shall be used on all trees and trunks greater than 5 inches (12.7 cm) dbh.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.6 - Tree Removal8.6.13 When manually felling trees, notches and back cuts shall be made at a height that enables the chain saw operator to safely begin the cut, control the tree or trunk, and have freedom of movement toward a retreat/escape path.
8.6.13.1 The two cuts that form the notch shall meet at a point called the apex and shall not cross that point or go beyond the point where they meet.
8.6.13.2 The notch cut used shall be an open-face notch, a conventional notch, or a Humboldt notch.
8.6.13.3 Notches shall be 45 degrees or greater and wide enough to guide the fall of the tree or trunk.
8.6.13.4 Notch depth should not exceed one-third the diameter of the tree.
8.6.13.5 Saw cuts made to form the notch and back cut shall leave suitable hinge wood to adequately control the fall of the tree.
8.6.13.6 With an open-face notch (greater than 70 degrees), the back cut should be at the same level as the apex of the notch. With a conventional notch or Humboldt notch, the back cut shall be 1 to 2 inches (2.5 to 5 cm) above the apex of the notch to provide an adequate platform to reduce kickback potential of the tree or trunk.
tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.6 - Tree Removal8.6.14 The hazard of barber chair should be considered when cutting trees under tension. Steps to prevent the sudden splitting of trunk wood should be taken. Preventive steps may include, but are not limited to, various back cut methods; wrapping a ratchet strap, rope, or chain around the tree above the notch and back cut area; or relieving the tension in or on the tree by slackening pull ropes or removing upper parts of the tree prior to felling.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.6 - Tree Removal8.6.15 Before making the back cut, there shall be a command such as “Stand clear” from the arborist operating the chain saw and a response such as “Clear” from the workers supporting the removal operation. Pre-arranged, two-way hand signals or two-way audible devices such as air horn or whistle signals may also be used. Only designated persons shall give such signals.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.6 - Tree Removal8.6.16 During manual tree felling operations, involved workers shall keep visual contact with the tree or trunk until it is on the ground.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.6 - Tree Removal8.6.17 Workers shall not approach closer than manufacturers’ or employers’ specified distances to mechanical operations, such as a rotary or flail mower, or boom-mounted saws, until all cutting has halted and the equipment operator has acknowledged that it is safe to do so.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.7 - Brush Removal and Chipping8.7.1 Prior to the start of chipping operations, vehicular and pedestrian traffic control around the work zone shall be established in accordance with applicable local, state, or federal requirements. See Section 3.5, Traffic Control.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.7 - Brush Removal and Chipping8.7.2 Brush and logs shall be placed in such a way that does not create hazards in the worksite.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.7 - Brush Removal and Chipping8.7.3 Loose-fitting items that could create an entanglement hazard (e.g., clothing, jewelry), aerial lift or climbing equipment, improperly worn PPE, or gauntlet-type gloves, shall not be worn while operating chippers.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.7 - Brush Removal and Chipping8.7.4 Personal protective equipment shall be worn when on the worksite of chipping operations in accordance with Section 3.3, Personal Protective Equipment (PPE), of this standard.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.7 - Brush Removal and Chipping8.7.5 During chipping operations, workers shall ensure that all throwlines and climbing and rigging lines are clear of the chipping area.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.7 - Brush Removal and Chipping8.7.6 Only persons trained in safe chipper operation may operate chippers. Training shall include, but is not limited to, inspection, starting, stopping, feeding, and shutdown. Training shall be provided for each type of chipper being used.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.7 - Brush Removal and Chipping8.7.7 Only persons authorized by the employer shall perform maintenance (see Annex C, General Safety Procedures That Apply to All Tree Work).tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.7 - Brush Removal and Chipping8.7.8 During chipping operations, hands, feet, or other parts of the body shall not pass beyond the plane of the infeed hopper. Leaning into or pushing material into infeed hoppers with feet is prohibited.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.7 - Brush Removal and Chipping8.7.9 When hand-feeding a chipper, brush and logs shall be fed into chippers from the side of the feed table center line. Brush and logs should be fed butt or cut end first, and the operator shall immediately turn and step away from the feed table when the brush is taken into the rotor or feed rollers.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.7 - Brush Removal and Chipping8.7.10 When hand-feeding a chipper during roadside operations, the operator should work from the curb or shoulder side whenever practical to prevent himself/herself from stepping into traffic or being pushed into traffic by the material that is being fed into the chipper.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.7 - Brush Removal and Chipping8.7.11 Brush chipper discharge chutes shall not be removed nor shall the cutter housing cover be opened or raised while any part of the chipper is turning or moving. Chippers shall not be used unless a discharge chute of sufficient length or design is provided that prevents personal contact with the blades (see Annex C, General Safety Procedures That Apply to All Tree Work).tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.7 - Brush Removal and Chipping8.7.12 Material, such as stones, nails, or sweepings shall not be fed into chippers.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.7 - Brush Removal and Chipping8.7.13 Limbs, logs, brush, and other woody material should be cut/prepared prior to feeding into the chipper.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.7 - Brush Removal and Chipping8.7.14 Small vegetation shall be fed into chippers with longer branches or pushed with a longer branch, push paddle, or suitable non-metallic tool.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.7 - Brush Removal and Chipping8.7.15 During chipping operations, operators shall be aware of potential pinch hazards between the machine and materials being chipped, and within the material itself.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.7 - Brush Removal and Chipping8.7.16 When using a winch in chipper operations, the winch line and/or winch line hook shall never pass beyond the plane of the infeed hopper. Once the material is controlled by the feeder wheels, the feeding process shall be stopped and the winch line and/or hook shall be properly stowed before proceeding.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.7 - Brush Removal and Chipping8.7.17 Should the chipper become clogged, procedures for the Control of Hazardous Energy (Annex C.2) shall be referenced and followed as appropriate.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.7 - Brush Removal and Chipping8.7.18 Due to the hazards of step and touch potential, if the distance between the aerial device and energized conductor(s) is unintentionally less than the required minimum approach distance (MAD), workers on the ground shall move away and remain clear of the aerial- device vehicle and attached equipment (e.g., chipper) until the required MAD is reestablished.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.7 - Brush Removal and Chipping8.7.19 Refer to Section 5.3, Brush Chippers, for additional information.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.7 - Brush Removal and Chipping8.7.20 Specialized material handling equipment, such as but not limited to skid-steers or mini-loaders (whether wheeled or tracked), when used in chipping operations, shall not create a hazard for other workers.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.8 - Limbing and Bucking8.8.1 Work plans for limbing and bucking operations shall be communicated to all workers in a job briefing before work begins.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.8 - Limbing and Bucking8.8.2 When more than one worker is involved in limbing, bucking, and moving debris from a tree, each shall be positioned and their duties organized so that the actions of one worker will not create a hazard for any other worker. Only one worker shall be cutting a single tree or single tree part during the limbing and bucking process.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.8 - Limbing and Bucking8.8.3 Before bucking or limbing wind-thrown trees, precautions shall be taken to prevent the root ball or butt log from striking a worker.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.8 - Limbing and Bucking8.8.4 Chain saws should be operated away from the vicinity of the legs and feet. Natural barriers, such as limbs between the saw and the body, should be employed where possible. While operating a chain saw, the preferred working position is on the uphill side of the work.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.8 - Limbing and Bucking8.8.5 The worker shall ensure firm footing before and during limbing and bucking. The worker shall not stand on loose debris or logs that may roll when the log being bucked is cut.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.8 - Limbing and Bucking8.8.6 Trees, limbs, or saplings under tension shall be considered hazardous. Appropriate cutting techniques and precautions shall be followed.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.8 - Limbing and Bucking8.8.7 When necessary to prevent rolling, logs shall be blocked with wood or other suitable material.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.8 - Limbing and Bucking8.8.8 Wedges should be used as necessary to prevent binding of the guide bar or chain when bucking.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.8 - Limbing and Bucking8.8.9 Cant hooks or peaveys should be used as an aid in rolling large or irregular logs.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.8 - Limbing and Bucking8.8.10 If mechanized equipment is used, the equipment operator shall establish an effective means of communication with other workers (see Subsection 8.5.11).tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.8 - Limbing and Bucking8.8.11 Workers shall not approach mechanized equipment operations until the equipment operator has acknowledged that it is safe to do so.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.9 - Pesticide Application8.9.1 Pesticide applicators shall obtain and remain current with all licensing/certification requirements as required by the appropriate state regulatory authority prior to using pesticides.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.9 - Pesticide Application8.9.2 Pesticide applicators shall follow all applicable laws and/or regulations pertaining to pesticide use, handling, and disposal.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.9 - Pesticide Application8.9.3 The applicator shall follow label instructions in regard to pesticide applications.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.9 - Pesticide Application8.9.4 Personal protective equipment shall be properly fitted, cleaned, maintained, and stored. Proper use of personal protective equipment as specified on the product label will reduce the risk of pesticide exposure to the applicator.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.9 - Pesticide Application8.9.5 Personal protective equipment shall not be stored with pesticides.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.9 - Pesticide Application8.9.6 Employee training shall be provided in the recognition of hazardous substances, proper handling, and emergency procedures in the event of a spill or accidental poisoning, as required by the OSHA 1910.1200 Hazard Communication standard and the Globally Harmonized System of Classification and Labelling of Chemicals (GHS).tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.9 - Pesticide Application8.9.7 Safety Data Sheets (SDS) for all products in inventory shall be reviewed with and made available to all affected employees. All SDSs pertaining to pesticides in use shall be readily available on the work site.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.9 - Pesticide Application8.9.8 The applicator shall follow pesticide label instructions in regard to laundering his/her clothing.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.9 - Pesticide Application8.9.9 The applicator should shower or bathe at the end of each workday.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.9 - Pesticide Application8.9.10 The employer shall provide a clean water source at the worksite, which may be used for emergency personal decontamination. Precautions shall be taken to prevent contamination of the clean water source. Drinking water and decontamination water shall be kept in separate containers and each labelled.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.9 - Pesticide Application8.9.11 The applicator shall not direct a solid spray column into contact with electrical conductors.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.9 - Pesticide Application8.9.12 Pesticides shall be stored in their original container or in a clearly marked service container.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.9 - Pesticide Application8.9.13 Pesticides shall be stored in locked compartments.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.9 - Pesticide Application8.9.14 Pesticide storage areas shall meet or exceed all applicable state and local regulations.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.9 - Pesticide Application8.9.15 An emergency action plan, including spill response materials and procedures, shall be available where pesticides are stored, transported, or handled.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.10 - Mixing Pesticides8.10.1 Pesticides shall be mixed in an area that is outdoors or in a well-ventilated, illuminated, enclosed area.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.10 - Mixing Pesticides8.10.2 Devices used for mixing and measuring pesticides shall be specifically designated and marked for pesticide use and shall be used for no other purpose.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.11 - High-Pressure Air-Excavation Equipment8.11.1 Personal protective equipment shall be required for the operator and all crew members within the worksite and shall include hard hat with attached face shield, hearing protection, eye protection, and gloves. Additionally, long pants, a long-sleeved shirt, and/or coveralls shall be worn.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.11 - High-Pressure Air-Excavation Equipment8.11.2 Respiratory protection should be worn when conditions warrant. When used, respiratory protection shall be in accordance with the OSHA 1910.134 Respiratory Protection standard.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.11 - High-Pressure Air-Excavation Equipment8.11.3 A proper worksite shall be identified; measures shall be taken to keep non-involved individuals clear of the worksite.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.11 - High-Pressure Air-Excavation Equipment8.11.4 The compressor operator shall understand and follow all operating instructions for the compressor.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.11 - High-Pressure Air-Excavation Equipment8.11.5 The air hose shall be properly attached and secured to the compressor prior to starting the compressor.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.11 - High-Pressure Air-Excavation Equipment8.11.6 Body parts shall not be placed in front of air jets.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.11 - High-Pressure Air-Excavation Equipment8.11.7 When the operator is finished, the air line shall be depressurized prior to uncoupling the air hose.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.12 - Fertilization/Soil Management8.12.1 Fertilization should be conducted in accordance with the ANSI A300 (Part 2) standard.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.12 - Fertilization/Soil Management8.12.2 All products should be used in accordance with manufacturers’ safety recommendations.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.12 - Fertilization/Soil Management8.12.3 Fertilizers shall be stored away from ignition sources and separate from petroleum products and pesticides.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.12 - Fertilization/Soil Management8.12.4 Smoking shall be prohibited in the fertilizer storage area.tree climbingZ133
ANSI Z133 Arborist Safety Requirements1 GENERAL1.1 - ScopeThis standard contains arboriculture safety requirements for pruning, repairing, maintaining, and removing trees; cutting brush; and for using equipment in such operations. (Note: Terms specific to the safe practice of arboriculture appear in boldface type at first use and are defined in Annex A, Glossary of Terms for ANSI Z133.)generalZ133
ANSI Z133 Arborist Safety Requirements1 GENERAL1.2 - PurposeThe purpose of this document is to provide safety standards for arborists and other workers engaged in arboricultural operations. It is intended as a guide to federal, state, and local authorities in drafting their regulations and may be adopted in whole or in part.generalZ133
ANSI Z133 Arborist Safety Requirements1 GENERAL1.3 - ApplicationThis standard is intended to serve as a reference for safety requirements that will apply to all employers or persons engaged in the business, trade, or performance of arboriculture for pay, operations of which include, but are not limited to, tree pruning, repairing, or maintaining; removing trees; cutting brush; or performing pest or soil management.generalZ133
ANSI Z133 Arborist Safety Requirements1 GENERAL1.3 - ApplicationThis standard may require situational modifications in response to personnel emergencies and is not intended to limit the options available to emergency responders.generalZ133
ANSI Z133 Arborist Safety Requirements1 GENERAL1.4 - Responsibilities of the EmployeeEach person (employee or otherwise) shall be responsible for his/her own safety while at work and shall comply with the appropriate federal or state occupational safety and health standards and all rules, regulations, and orders that are applicable to his/her own actions and conduct.generalZ133
ANSI Z133 Arborist Safety Requirements2 NORMATIVE REFERENCES2.1 - GeneralThis standard contains references to other American National Standards and federal regulations, which, through reference in this text, constitute provisions of this American National Standard. See Annex D, Additional Resources, for a list of these and other applicable informative references. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this American National Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated in Annex D.normative referencesZ133
ANSI Z133 Arborist Safety Requirements2 NORMATIVE REFERENCES2.1 - GeneralBecause of the many specialized procedures utilized during arboricultural operations, it must be emphasized that exceptions to provisions of these standards may be acceptable and that flexibility and/or a decision as to the applicability of these standards to professional operations may be required.normative referencesZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.1 - General3.1.1 Tools and equipment used in arboricultural operations shall comply with applicable OSHA regulations and/or ANSI standards. In the absence of applicable OSHA/ANSI guidance, the requirements of this standard shall be followed.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.1 - General3.1.2 Employers shall instruct their employees in the proper use, inspection, and maintenance of personal protective equipment (PPE), tools (hand and powered), and other equipment, including ropes and lines.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.1 - General3.1.3 Employers shall require that appropriate safety-related work practices be followed in accordance with applicable OSHA and consensus standards, including, but not limited to ANSI and ASTM. As applicable, manufacturers’ recommendations should be followed. See Section 5, Safe Use of Vehicles, Mobile and Towed Equipment Used in Arboriculture, for specific standards regarding vehicles and mobile equipment.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.2 - Emergency Procedures and Readiness3.2.1 All personnel engaged in arboricultural operations shall be instructed in the correct procedures for emergency response, including 911 calls and other applicable emergency phone numbers.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.2 - Emergency Procedures and Readiness3.2.2 The employer shall provide and maintain a first-aid kit that meets the requirements of ANSI Z308.1, with contents appropriate for the type of job and number of workers.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.2 - Emergency Procedures and Readiness3.2.3 Instruction shall be provided in the identification, preventive measures, and first-aid treatment of common poisonous plants (poison ivy, poison oak, and poison sumac), stinging and biting insects, and other pests found in the area in which work is to be performed.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.2 - Emergency Procedures and Readiness3.2.4 Employees who may be faced with a rescue decision shall receive training in emergency response and rescue procedures appropriate and applicable to the work to be performed, as well as training to recognize the hazards inherent in rescue efforts (see Annex F, Aerial Rescue Flowchart).general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.2 - Emergency Procedures and Readiness3.2.5 For field crews involving two or more workers at a work location, at least two workers trained in first aid/CPR shall be available. However, only one trained person need be available if all new employees are trained in first aid within three months of their hiring dates.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.3 - Personal Protective Equipment (PPE)3.3.1 Personal protective equipment (PPE), as outlined in this section, shall be required when there is a reasonable probability of injury or illness that can be prevented by such protection.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.3 - Personal Protective Equipment (PPE)3.3.2 The employer shall assess the worksite to determine if hazards are present or are likely to be present and what type of personal protective equipment is required.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.3 - Personal Protective Equipment (PPE)3.3.3 Training shall be provided on the inspection, use, care, maintenance, fit, and replacement of personal protective equipment.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.3 - Personal Protective Equipment (PPE)3.3.4 Workers engaged in arboricultural operations shall wear head protection (helmets) that conforms to ANSI Z89.1. Class E helmets shall be worn when working in proximity to electrical conductors in accordance with ANSI Z89.1. Workers shall not place reliance on the dielectric capabilities of such helmets.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.3 - Personal Protective Equipment (PPE)3.3.5 Hearing protection provided by the employer shall be worn when it is not practical to decrease or isolate noise levels that exceed acceptable standards. The employer shall provide employees protection against the effects of noise exposure when sound levels exceed an 8-hour, time-weighted average (TWA) of 85 decibels (dB).general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.3 - Personal Protective Equipment (PPE)3.3.6 Eye protection shall comply with ANSI Z87.1 and shall be worn when engaged in arboricultural operations.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.3 - Personal Protective Equipment (PPE)3.3.7 Clothing and footwear appropriate to the known worksite hazards shall be approved by the employer and worn by the employee.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.3 - Personal Protective Equipment (PPE)3.3.8 Cut-resistant leg protection that meets or exceeds ASTM F1414 and ASTM F1897 shall be worn while operating a chain saw during ground operations. Cut-resistant leg protection shall be maintained in accordance with manufacturer’s recommendations.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.3 - Personal Protective Equipment (PPE)3.3.9 Face protection shall comply with applicable federal regulations as well as with ANSI Z87.1.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.3 - Personal Protective Equipment (PPE)3.3.10 Respiratory protection shall comply with applicable federal regulations and with ANSI Z88.2.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.4 - Job Briefing and Worksite Set-up3.4.1 A qualified arborist shall determine whether direct supervision is needed on a worksite.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.4 - Job Briefing and Worksite Set-up3.4.2 Before digging, underground utilities shall be marked by utility-locating services.
3.4.2.1 Many utility-based locating services will not locate privately owned underground lines, such as, but not limited to, irrigation, electrical wires, and propane lines. Further resources or research may be necessary to locate underground utilities on private properties.
general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.4 - Job Briefing and Worksite Set-up3.4.3 A job briefing shall be performed by the qualified arborist in charge before the start of each job. The briefing shall be communicated to all affected workers. An employee working alone need not conduct a job briefing. However, the employer shall ensure that the tasks are being performed as if a briefing were required.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.4 - Job Briefing and Worksite Set-up3.4.4 Before commencing operations, a communication protocol shall be established or reviewed between arborists aloft and personnel working on the ground. Verbal communication by voice or radio shall employ a command and response (C&R) protocol. “Stand Clear” as the “C” from aloft and “Clear” as the “R” from the ground are examples. Hand signals or whistles may also be used. Eye contact with, or line-of-sight between, the arborist aloft and the ground person should also be established when communicating.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.4 - Job Briefing and Worksite Set-up3.4.5 The arborist in charge shall establish a plan to safely manage the worksite. Communications among arborists aloft and other workers on the ground shall be established before commencing operations. Predetermined, non-verbal communication such as whistles, two-way hand signals, or radios may also be used.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.4 - Job Briefing and Worksite Set-up3.4.6 When dropping or lowering trunks, branches, fruit, or equipment, a landing area (drop zone) should be designated.
3.4.6.1 People and valuable objects shall be protected or excluded from the drop zone when active.
3.4.6.2 A visible drop zone may be designated as an aid to avoidance of falling objects.
general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.4 - Job Briefing and Worksite Set-up3.4.7 An inspection shall be made by a qualified arborist to determine whether an electrical hazard exists before performing arboricultural operations.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.4 - Job Briefing and Worksite Set-up3.4.8 A qualified arborist shall visually inspect the tree, including the root collar and the area immediately surrounding the tree, for hazards before anyone climbs, otherwise enters, or performs any work on the tree.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.4 - Job Briefing and Worksite Set-up3.4.9 When definite indicators of decay, weakly attached branches, or dead bark are seen, the qualified arborist shall determine if the tree can withstand the forces to be applied during the work.
3.4.9.1 If there is question as to the condition of the tree, relative to the task to be performed, work shall not commence until a more thorough assessment can be made.
general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.4 - Job Briefing and Worksite Set-up3.4.10 A second arborist, an arborist trainee, or other worker trained in emergency procedures shall be within visual or voice communication during arboricultural operations above 12 feet (3.65 m) that are not subject to the requirements of Subsection 4.3.9.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.5 - Traffic Control3.5.1 Traffic and pedestrian control around the worksite shall be established prior to the start of all arboricultural operations.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.5 - Traffic Control3.5.2 Arborists and other workers having specific temporary traffic control zone responsibilities shall be trained in temporary traffic control techniques, device usage and placement, and how to work next to traffic in a manner that minimizes their exposure.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.5 - Traffic Control3.5.3 Arborists and other workers exposed to risks of moving roadway traffic shall wear high-visibility safety apparel meeting the requirements of ANSI/ISEA 107.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.5 - Traffic Control3.5.4 The temporary traffic control zone should impede the flow of vehicular traffic as little as possible. Arborists and other workers should use the necessary devices that get the road user’s attention and provide positive direction in accordance with the Manual on Uniform Traffic Control Devices (MUTCD).general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.5 - Traffic Control3.5.5 Pedestrians should have separate movement from the worksite and vehicular traffic, including bicycles, with a safe, convenient, and accessible path.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.6 - Fire Protection3.6.1 All personnel shall be instructed in the use and location of vehicle-mounted fire extinguishers.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.6 - Fire Protection3.6.2 Equipment shall be fueled only (a) when the engine has been shut down; (b) from approved containers; and (c) at least 10 feet (3.05 m) from any operating equipment. Spilled fuel shall be cleaned up before restarting.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.6 - Fire Protection3.6.3 Flammable liquids shall be stored, handled, and dispensed from approved and clearly marked containers.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.6 - Fire Protection3.6.4 Equipment shall not be operated within 10 feet (3.05 m) of areas in which refueling hasrecently taken place.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.6 - Fire Protection3.6.5 Smoking shall be prohibited when working around or handling flammable liquids or while wearing clothing contaminated by fuel.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.6 - Fire Protection3.6.6 Clothing contaminated with fuel shall be changed, removed, or replaced as soon as possible.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.6 - Fire Protection3.6.7 Open flame and other sources of ignition shall be avoided.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.6 - Fire Protection3.6.8 Dead and/or combustible material shall be kept clear of hot and/or operating equipment.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements3 GENERAL SAFETY REQUIREMENTS3.6 - Fire Protection3.6.9 Where required, all internal or external combustion engines shall be equipped with a spark arrester that meets the requirements established by SAE Standard J335 or USDA Forest Service Specification 5100-1. Federal requirements are explained in 36 CFR 261.52.general safety requirementsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.1 - General4.1.1 All applicable requirements in Section 3, General Safety Requirements, shall apply to this section.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.1 - General4.1.2 The employer shall train each employee that all overhead and underground electrical conductors, guy wires, pole grounds, and communication wires and cables shall be considered energized with potentially fatal voltages.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.1 - General4.1.3 Arborists’ training and degree of training in electrical hazards shall be determined by the risk to the employee for hazard(s) involved.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.1 - General4.1.4 All arborists and other workers shall be instructed that
(a) the human body is conductive and poses little resistance to electric current and will provide a path for the flow of electricity to a grounded object or to the ground itself;
(b) direct contact or indirect contact (phase-to-ground contact) with an electrical conductor, energized tree limb, tool, or equipment, or other energized object may lead to electric shock, significant injury, or death;
(c) the woody parts of trees, leaves, branches, needles, palm fronds, etc., are conductive;
(d) simultaneous contact with two separate energized conductors (phase-to-phase contact) will cause electric shock that may result in serious or fatal injury;
(e) electrical shock may occur as a result of ground fault when a person stands near a grounded object that becomes energized (e.g., an uninsulated part of an aerial device comes into contact with a conductor); and
(f) in the event of a downed energized electrical conductor or energized grounded object (e.g., guy wires or pole grounds), there exists the hazard of touch and step potential.
electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.1 - General4.1.5 An inspection shall be made by a qualified arborist to determine whether an electrical hazard exists before climbing, otherwise entering, or performing work in or on a tree.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.1 - General4.1.6 When determining the presence of an electrical hazard, consideration shall be given to the "potential movement of an electrical supply line due to wind, load sag, or other factors that affect the line’s position in relation to the work.
"
electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.1 - General4.1.7 Arborists not qualified by training and experience to work within 10 feet (3.05 m) of electrical conductors shall maintain at all times the minimum approach distances (MAD) shown in Table 1, measured radially.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.1 - General4.1.8 Arborists should climb on the side of the tree that is away from energized electrical conductors.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.1 - General4.1.9 Climbers’ body, gear, and their conductive equipment shall be maintained at the required minimum approach distance (MAD) or greater, shown in Tables 1, 2, or 3, as applicable.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.1 - General4.1.10 The climber’s tie-in point should be above the climber’s work position and located in such a way that a slip would swing the arborist away from any energized electrical conductor or other identified hazard.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.1 - General4.1.11 A conductive rope may not be used within the minimum approach distances (MAD) shown in Table 1, 2, or 3, as applicable.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.1 - General4.1.12 Portable ladders shall not have conductive side rails if they are used where the employee or the ladder could contact exposed energized parts.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.1 - General4.1.13 Ladders, platforms, and aerial devices, including insulated aerial devices, shall be subject to minimum approach distances in accordance with Table 1, 2, or 3, as applicable.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.1 - General4.1.14 Due to the hazards of step and touch potential, if the distance between the aerial device and energized conductor(s) is unintentionally less than the required minimum approach distance (MAD), workers on the ground shall move away and remain clear of the aerial- device vehicle and attached equipment (e.g., chipper) until the required MAD is reestablished.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.1 - General4.1.15 Emergency response to an electric contact shall be performed in accordance with Section 3.2, Emergency Procedures and Readiness.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.1 - General4.1.16 Arboricultural operations in proximity to energized electrical conductors shall not be performed during adverse weather conditions, such as thunderstorms, high winds, snow storms, or ice storms.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.2 - Working in Proximity to Electrical Hazards – Incidental Line Clearance4.2.1 The items contained in Section 4.1, General, shall always be included in the review of this section.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.2 - Working in Proximity to Electrical Hazards – Incidental Line Clearance4.2.2 Workers shall be trained on safety-related work practices that protect employees against the voltage level to which they are exposed.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.2 - Working in Proximity to Electrical Hazards – Incidental Line Clearance4.2.3 Safety-related work practices shall be employed to prevent electric shock or other injuries resulting from either direct or indirect electrical contacts and shall be consistent with the nature and extent of the electrical hazards present.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.2 - Working in Proximity to Electrical Hazards – Incidental Line Clearance4.2.4 Training for qualification of qualified incidental line clearance arborist requires a minimum of (a) the skills and techniques necessary to distinguish exposed live parts from other parts of electric equipment; (b) the skills and techniques necessary to determine the nominal voltage of exposed live parts; and (c) the minimum approach distances (MAD) specified in Table 2 and the corresponding voltages to which the qualified person will be exposed.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.2 - Working in Proximity to Electrical Hazards – Incidental Line Clearance4.2.5 Before work is performed within the minimum approach distance (MAD) without insulated tools, overhead energized lines shall be de-energized. It shall be the responsibility of the system owner/operator of the electrical system to make the system safe.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.2 - Working in Proximity to Electrical Hazards – Incidental Line Clearance4.2.6 When a qualified incidental line clearance arborist is working in the vicinity of overhead lines, whether in an elevated position or on the ground, the person shall not approach or take any conductive object closer to exposed energized parts than shown in Table 2.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.2 - Working in Proximity to Electrical Hazards – Incidental Line Clearance4.2.7 Branches and other parts of trees within the minimum approach distances (MAD) which have been browned or charred by past electrical arcing or contact should be considered likely to become re-energized without warning and thus should be treated as energized. Climbing of trees in such condition should be avoided.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.2 - Working in Proximity to Electrical Hazards – Incidental Line Clearance4.2.8 Tools that are not rated as insulated for the voltage to which they are exposed shall be considered conductive.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.3 - Working in Proximity to Electrical Hazards – Utility Line Clearance4.3.1 The items contained in Section 4.1, General, shall always be included in the review of this section.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.3 - Working in Proximity to Electrical Hazards – Utility Line Clearance4.3.2 The employer shall verify that each line clearance arborist is qualified to work within proximity to electrical hazards that the arborist is exposed to and has been trained in the following topics:
(a) To be familiar with safety-related work practices, procedures, and other requirements that pertain to his or her job assignments.
(b) On emergency and work-related rescue procedures that are related to his or her work and are necessary for the safety of the worker.
electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.3 - Working in Proximity to Electrical Hazards – Utility Line Clearance4.3.3 Qualified line clearance arborists shall also be trained and competent in: (a) The skills and techniques necessary to distinguish exposed, energized parts from other parts of electric equipment. (b) The skills and techniques necessary to determine the nominal voltage of exposed energized parts. (c) The MAD specified in Table 3 and the corresponding voltages to which the qualified line clearance arborist will be exposed and the skills and techniques necessary to maintain those distances, for the nominal voltage present.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.3 - Working in Proximity to Electrical Hazards – Utility Line Clearance4.3.4 The employer shall ensure that each employee has demonstrated proficiency in the work practices involved before that employee is considered as having completed the training.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.3 - Working in Proximity to Electrical Hazards – Utility Line Clearance4.3.5 When qualified line-clearance arborist trainees are assigned to work where an electrical hazard exists, the qualified line-clearance arborist trainees shall be under the direct supervision of qualified line-clearance arborists.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.3 - Working in Proximity to Electrical Hazards – Utility Line Clearance4.3.6 Qualified line-clearance arborists and qualified line-clearance arborist trainees performing line clearance after a storm or under similar conditions shall be trained in the hazards associated with this type of work and in the recognition of the hazards of step potential.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.3 - Working in Proximity to Electrical Hazards – Utility Line Clearance4.3.7 Line-clearance operations shall be suspended when adverse weather conditions or emergency conditions develop involving energized electrical conductors. Electrical system owners/operators shall be notified immediately.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.3 - Working in Proximity to Electrical Hazards – Utility Line Clearance4.3.8 When performing line-clearance work for the electrical system owner/operator (host employer) – it shall be the responsibility of the contract employer receiving host utility information to communicate it and any hazardous conditions relevant to the affected workers performing the affected work.
(a) Before work begins, the contract employer and the host employer shall coordinate their work rules and procedures so that each employee of the contract employer and the host employer is protected.
(b) Before work begins, the contract employer shall advise the host employer of any unique hazardous conditions presented by the contract employer’s work.
(c) The contract employer shall advise the host utility/employer of any unanticipated hazardous conditions, of the electrical system, found during the contract employer’s work. This information shall be provided to the host utility within two working days after discovering the hazardous condition.
electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.3 - Working in Proximity to Electrical Hazards – Utility Line Clearance4.3.9 A second qualified line-clearance arborist or line-clearance arborist trainee (with a minimum of training in emergency procedures), shall be within unassisted voice communication and should be within visual contact during line-clearance operations aloft when a qualified line-clearance arborist or line-clearance arborist trainee must approach closer than 10 feet (3.05 m) to any energized electrical conductor in excess of 750 volts (primary conductor) or when
(a) branches or limbs are being removed, which cannot first be cut (with an insulated pole pruner/pole saw) to sufficiently clear electrical conductors, so as to avoid contact; and/or
(b) roping is required to remove branches or limbs from such electrical conductors.
electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.3 - Working in Proximity to Electrical Hazards – Utility Line Clearance4.3.10 Insulating pruning tools shall be designed and constructed to withstand the minimum testing, as outlined in Annex J, Live-Line Tools.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.3 - Working in Proximity to Electrical Hazards – Utility Line Clearance4.3.11 Qualified line-clearance arborists and line-clearance arborist trainees shall maintain minimum approach distances from energized electrical conductors in accordance with Table 3.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements4 ELECTRICAL HAZARDS4.3 - Working in Proximity to Electrical Hazards – Utility Line Clearance4.3.12 If the minimum approach distance (shown in Table 3) cannot be maintained during the arboricultural operations, the qualified line-clearance arborist shall request that the electrical system owner/operator’s designated supervisor in charge coordinate communications and operations between the electrical system owner/operator and the qualified line-clearance arborist to mitigate the electrical hazard. Mitigation options should include all safe, OSHA-compliant, and practical work methods, and, where necessary, de-energizing, testing, isolating, and grounding the electrical conductors by the electrical system owner/operator (see Annex H, Electrical Hazard Abatement). The designated electrical system owner/operator employee and the designated qualified line- clearance arborist in charge shall confirm that protective ground(s) have been installed as close as is practical to the line clearance work to be performed to prevent hazardous differences in electrical potential.electrical hazardsZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.1 - Vehicles and Mobile Equipment5.1.11 Riding or working outside or on top of equipment shall not be permitted unless the equipment is specifically designed for that purpose.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.1 - Vehicles and Mobile Equipment5.1.12 Hoisting or lifting equipment mounted on vehicles shall be used within rated capacities as stated by the manufacturers’ specifications.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.1 - Vehicles and Mobile Equipment5.1.13 Equipment with an obstructed view to the rear, particularly those with towed equipment, should be backed up only when absolutely necessary. The vehicle shall not be backed up unless the vehicle has a reverse signal alarm audible above the surrounding noise level or when a spotter signals that it is safe to do so, or, immediately before backing up, the driver determines through a visual walk-around inspection that there are no people or obstructions in the path of the vehicle.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.1 - Vehicles and Mobile Equipment5.1.14 When equipment is left unattended, attachments should be stowed, cradled, or lowered to the ground; keys shall be removed from the ignition; the wheels chocked; and, if applicable, the parking brake applied.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.1 - Vehicles and Mobile Equipment5.1.15 When performing maintenance or repairs, except where manufacturers’ procedures require otherwise:
(a) equipment shall be turned off;
(b) keys shall be removed from the ignition;
(c) all rotating parts and moving parts shall be stopped and secured, if applicable; and
(d) all sources of energy, including, but not limited to: mechanical, electrical, hydraulic, pneumatic, chemical, and thermal energy shall be verified to be released.

Defects or malfunctions affecting the safe operation of equipment shall be corrected before such equipment is placed into use (see Annex C, General Safety Procedures That Apply to All Tree Work).
SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.1 - Vehicles and Mobile Equipment5.1.16 When towing:
5.1.16.1 Safety chains shall be crossed under the tongue of the equipment being towed and adjusted to the appropriate length. The safety chains shall not be twisted or knotted when connecting or when connected to the tow vehicle.
5.1.16.2 Connecting links and repair links shall be of the same size and grade as the safety chain(s) being used.
5.1.16.3 All coupling devices shall be in place and in proper working condition (e.g., pins, electrical connections, emergency break-away devices). Equipment shall meet the towing capacities necessary for the intended load.
5.1.16.4 Manufacturer towing capacity and Gross Combination Weight Rating (GCWR) shall not be exceeded except where permitted by law.
SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.1 - Vehicles and Mobile Equipment5.1.17 Prior to being detached, towed equipment shall be chocked or otherwise secured in place.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.1 - Vehicles and Mobile Equipment5.1.18 Precautions should be taken to ensure that exhaust systems do not present a fire hazard.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.1 - Vehicles and Mobile Equipment5.1.19 Equipment operated off-road shall be operated in the appropriate gear and speed relative to the operating environment.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.1 - Vehicles and Mobile Equipment5.1.20 Operator protective structures shall meet the requirements of the applicable Society of Automotive Engineers (SAE) standard.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.1 - Vehicles and Mobile Equipment5.1.21 Equipment body props shall be installed and used when the dump body is raised and workers need to access the area underneath. The equipment props should be accessible without reaching between the raised part of the equipment and the chassis or body of the equipment.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.1 - Vehicles and Mobile Equipment5.1.22 Drivers shall know and not exceed the Gross Vehicle Weight Rating (GVWR) and/or Gross Combination Weight Rating (GCWR) of any vehicle and towed equipment prior to moving the equipment.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.1 - Vehicles and Mobile Equipment5.1.23 Drivers shall know the height of the vehicle and any towed equipment prior to moving the vehicle or towed equipment and shall not attempt to drive under structures lower than the vehicle height.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.2 - Aerial Devices5.2.1 The items contained in Section 5.1, Vehicles and Mobile Equipment, shall always be included in the review of this section.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.9 - Equipment-Mounted Winches5.9.5 Operators shall be aware of the hazards of load or winch line breakage and ensure that all personnel remain clear of the recoil area in the event of load or winch line breakage.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.9 - Equipment-Mounted Winches5.9.6 All winch operators shall be properly trained and be aware of the inherent dangers associated with winch operations.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.9 - Equipment-Mounted Winches5.9.7 Operators shall be aware of the winch line at all times during extension and ensure that it does not become a hazard to personnel or machinery.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.9 - Equipment-Mounted Winches5.9.8 Winch systems and winch lines shall be used only as intended and instructed by the manufacturer.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.9 - Equipment-Mounted Winches5.9.9 A winch line should not be wrapped around a load. During winching operations of loads that do not have a manufactured attachment point, the load should be secured using a sling.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.9 - Equipment-Mounted Winches5.9.10 The winch shall never be used with personnel, including the operator, within the span of the winch line and the winch.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.9 - Equipment-Mounted Winches5.9.11 Pinch point hazards develop during winching operations; therefore, all operators involved in the winching operation shall constantly be aware of such hazards and stand clear of these areas.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.9 - Equipment-Mounted Winches5.9.12 All loads shall be pulled in such a manner as to avoid angles that may result in tipping, cause the vehicle to become unstable, or result in unintended movement of the vehicle.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.9 - Equipment-Mounted Winches5.9.13 Pulling loads from the side requires special equipment and techniques. Therefore, loads shall be pulled in line with the winch unless the winch is properly equipped with a fair lead and the operator is trained to pull loads at an angle.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.9 - Equipment-Mounted Winches5.9.14 The operator shall ensure that the vehicle supporting the winch is secured to avoid unintended movement.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.9 - Equipment-Mounted Winches5.9.15 The operator shall ensure that all rigging points comply with Section 8.5, Rigging.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.9 - Equipment-Mounted Winches5.9.16 An effective means of communication shall be established and used with all workers involved in the winching operations (see Subsection 8.5.11).SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.9 - Equipment-Mounted Winches5.9.17 Winch lines shall be compatible with the winch design and shall meet manufacturers’ specifications.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements5 SAFE USE OF VEHICLES, MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTURE5.9 - Equipment-Mounted Winches5.9.18 When using a winch in chipper operations, the operator shall ensure that the winch line is properly stored before initiating chipper operations. EXCEPTION: A winch line may be used to assist with positioning material onto the feed table and infeed hopper. Once the material has been positioned the winch line must be properly stored before continuing chipping operations.SAFE USE OF VEHICLES MOBILE AND TOWED EQUIPMENT USED IN ARBORICULTUREZ133
ANSI Z133 Arborist Safety Requirements6 PORTABLE POWER HAND TOOLS6.1 - General6.1.1 All applicable requirements in Section 3, General Safety Requirements, shall apply to this section.portable power hand toolsZ133
ANSI Z133 Arborist Safety Requirements6 PORTABLE POWER HAND TOOLS6.1 - General6.1.2 The purpose of this section is to provide guidelines for arborists and other workers pertaining to the safe use and care of portable power hand tools.portable power hand toolsZ133
ANSI Z133 Arborist Safety Requirements6 PORTABLE POWER HAND TOOLS6.1 - General6.1.3 The employer should follow the manufacturer’s operating, maintenance, and safety instructions, unless the employer demonstrates that a greater hazard is posed by following the manufacturer’s instructions.portable power hand toolsZ133
ANSI Z133 Arborist Safety Requirements6 PORTABLE POWER HAND TOOLS6.1 - General6.1.4 Before starting or operating portable power hand tools, the operators shall communicate with and ensure that all other workers are clear of the equipment, the swing arc of the cutting attachment, and the immediate worksite.portable power hand toolsZ133
ANSI Z133 Arborist Safety Requirements6 PORTABLE POWER HAND TOOLS6.1 - General6.1.5 Communication shall be established between the arborists working aloft, either in a tree or from an aerial device, and arborists and other workers on the ground, before starting or otherwise using any portable power hand tools. The command “stand clear” from aloft and the response “clear” from the ground are terms that may be used for this purpose. Pre-arranged, two-way hand signals may also be used. Workers shall stay out of the drop zone until it has been communicated by the qualified arborist, qualified arborist trainee, or worker aloft that it is safe to enter.portable power hand toolsZ133
ANSI Z133 Arborist Safety Requirements6 PORTABLE POWER HAND TOOLS6.1 - General6.1.6 When a chain saw or power hand tool is carried aloft and is not in use, it shall be secured against falling.portable power hand toolsZ133
ANSI Z133 Arborist Safety Requirements6 PORTABLE POWER HAND TOOLS6.2 - Portable Electric Power Tools6.2.1 The items contained in Section 6.1, General, shall always be included in the review of this section.portable power hand toolsZ133
ANSI Z133 Arborist Safety Requirements6 PORTABLE POWER HAND TOOLS6.2 - Portable Electric Power Tools6.2.2 Corded electric power tools shall not be used in trees or aerial devices near energized electrical conductors where there is a possibility of power tools or supply cords contacting the conductor.portable power hand toolsZ133
ANSI Z133 Arborist Safety Requirements6 PORTABLE POWER HAND TOOLS6.2 - Portable Electric Power Tools6.2.3 All corded portable electric power tools shall be (a) equipped with three-wire cords having the ground wire permanently connected to the tool frame and a means for grounding the other end; or (b) double insulated and permanently labeled as “double insulated”; or (c) connected to power supplies by means of an isolating transformer or other isolated power supply.portable power hand toolsZ133
ANSI Z133 Arborist Safety Requirements6 PORTABLE POWER HAND TOOLS6.2 - Portable Electric Power Tools6.2.4 Extension cords shall be maintained in safe condition. Exposed metal sockets shall not be used.portable power hand toolsZ133
ANSI Z133 Arborist Safety Requirements6 PORTABLE POWER HAND TOOLS6.2 - Portable Electric Power Tools6.2.5 Arborists and other workers shall prevent cords from becoming entangled, damaged, or cut by blades and bits and shall avoid laying extension cords in water.portable power hand toolsZ133
ANSI Z133 Arborist Safety Requirements6 PORTABLE POWER HAND TOOLS6.3 - Chain Saws6.3.1 The items contained in Section 6.1, General, shall always be included in the review of this section.portable power hand toolsZ133
ANSI Z133 Arborist Safety Requirements6 PORTABLE POWER HAND TOOLS6.3 - Chain Saws6.3.2 Chain saws shall not be operated unless the manufacturer’s safety devices are in proper working order. Chain saw safety devices shall not be removed or modified.portable power hand toolsZ133
ANSI Z133 Arborist Safety Requirements6 PORTABLE POWER HAND TOOLS6.3 - Chain Saws6.3.3 A stable body position shall be maintained when starting a chain saw.portable power hand toolsZ133
ANSI Z133 Arborist Safety Requirements6 PORTABLE POWER HAND TOOLS6.3 - Chain Saws6.3.4 Drop-starting a chain saw is prohibited. A chain saw shall be started with the chain brake engaged and the operator holding the saw firmly in a manner that minimizes movement of the saw when pulling the starter handle.portable power hand toolsZ133
ANSI Z133 Arborist Safety Requirements6 PORTABLE POWER HAND TOOLS6.3 - Chain Saws6.3.5 A chain saw shall be operated with two hands at all times, one hand on each handle with thumbs wrapped around the handles.portable power hand toolsZ133
ANSI Z133 Arborist Safety Requirements6 PORTABLE POWER HAND TOOLS6.3 - Chain Saws6.3.5.1 The operator shall operate the chain saw with the left hand and thumb gripped firmly around the forward handle and the right hand and thumb gripped firmly around the rear handle, unless it is not practicable, and the employer demonstrates that a greater hazard is posed by operating the chain saw that way in that particular situation.portable power hand toolsZ133
ANSI Z133 Arborist Safety Requirements6 PORTABLE POWER HAND TOOLS6.3 - Chain Saws6.3.6 Arborists shall be tied in and use a second means of being secured (e.g., lanyard, work- positioning lanyard or second climbing line) when operating a chain saw in a tree. Using two work-positioning lanyards or both ends of a two-in-one work-positioning lanyard shall not be considered acceptable as two means of being secured when using a chain saw in a tree.
EXCEPTION to 6.3.6: When the employer demonstrates that a greater hazard is posed by using a second means of being secured while operating a chain saw in that particular situation.
portable power hand toolsZ133
ANSI Z133 Arborist Safety Requirements6 PORTABLE POWER HAND TOOLS6.3 - Chain Saws6.3.7 The chain brake shall be engaged or the engine shut off before setting a chain saw down.portable power hand toolsZ133
ANSI Z133 Arborist Safety Requirements6 PORTABLE POWER HAND TOOLS6.3 - Chain Saws6.3.8 When a chain saw is being carried more than two steps, the chain brake shall be engaged or the engine shut off. The chain saw shall be carried in a manner that will prevent operator contact with the cutting chain and the muffler.portable power hand toolsZ133
ANSI Z133 Arborist Safety Requirements6 PORTABLE POWER HAND TOOLS6.3 - Chain Saws6.3.9 The chain saw operator shall be certain of a stable body position before starting to cut. The chain saw shall not be used in a position or at a distance that could cause the operator to become off-balance, have insecure footing, or relinquish a firm grip on the saw. A chain saw shall not be used above shoulder height unless the employer demonstrates that a greater hazard is posed by operating the chain saw that way in that particular situation.portable power hand toolsZ133
ANSI Z133 Arborist Safety Requirements6 PORTABLE POWER HAND TOOLS6.4 - Powered Pole Tools and Backpack Power Units6.4.1 The items contained in Section 6.1, General, shall always be included in the review of this section.portable power hand toolsZ133
ANSI Z133 Arborist Safety Requirements6 PORTABLE POWER HAND TOOLS6.4 - Powered Pole Tools and Backpack Power Units6.4.2 Powered pole tools with poles made of metal or other conductive material shall not be used in operations where electrical hazards exist. See Subsection 8.3.5 of this standard.portable power hand toolsZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.1 - General7.1.1 All applicable requirements in Section 3, General Safety Requirements, shall apply to this section.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.1 - General7.1.2 Correct hand tools and equipment shall be selected for the job.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.5 - Ladders7.5.4 All ladders shall be inspected before use and removed from service if found defective.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.5 - Ladders7.5.5 Cleats, metal points, skid-resistant feet, lashing, or other effective means of securing the ladder shall be used when there is danger of slipping.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.5 - Ladders7.5.6 Ladders shall not be used as bridges or inclined planes to load or handle logs or other material.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.5 - Ladders7.5.7 Ladders shall be supported while in storage to prevent sagging. Except when on mobile equipment, ladders should be stored under suitable cover, protected from the weather, and kept in a dry location away from excessive heat.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.5 - Ladders7.5.8 The third, or hinged, leg of a tripod/orchard ladder shall be braced or fastened when on hard or slick surfaces.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements7 HAND TOOLS AND LADDERS7.5 - Ladders7.5.9 All ladders shall be used in accordance with the manufacturers’ recommendations and shall not be altered in a way that contradicts those recommendations.hand tools and laddersZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.1 - Climbing Procedures8.1.1 All applicable requirements in Section 3, General Safety Requirements, shall apply to this section.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.1 - Climbing Procedures8.1.2 A second arborist, an arborist trainee, or other worker trained in emergency procedures shall be within visual or voice communication during arboricultural operations above 12 feet (3.65 m) that are not subject to the requirements of Subsection 4.3.9.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.1 - Climbing Procedures8.1.3 Arborists shall inspect climbing lines, worklines (line, workline), work-positioning lanyards, and other climbing equipment for damage, cuts, abrasion, and/or deterioration before each use and shall remove them from service, per manufacturers’ guidelines if applicable, if signs of excessive wear or damage are found. Climbing lines or worklines that are removed from service may be used for other noncritical purposes if deemed suitable for such use by a qualified person.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.1 - Climbing Procedures8.1.4 While working aloft, the climber shall have available a climbing line and at least one other means of being secured on his/her person at all times (e.g., an arborist climbing line and a work-positioning lanyard). Two means of being secured shall be used when the climber determines that it is advantageous.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.1 - Climbing Procedures8.1.5 The climber shall have a hand saw available while working aloft. Hand saws aloft shall either have a scabbard or be of the folding type that covers the cutting teeth when closed.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.1 - Climbing Procedures8.1.6 The arborist shall be secured at all times while ascending the tree, including when using climbing spurs/gaffs. The arborist shall be tied in once the work begins and shall remain tied in until the work is completed and he/she has returned to the ground. The arborist shall be secured when repositioning the climbing line. When repositioning, the arborist shall preload the new tie-in point with his/her full weight before releasing the current means of being secured.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.1 - Climbing Procedures8.1.7 While ascending a ladder to gain access to a tree, the arborist shall not work from or leave the ladder until he/she is tied in or secured.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.1 - Climbing Procedures8.1.8 Hands and feet should be placed on separate limbs, if possible, and three points of contact should be maintained with the tree while climbing.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.1 - Climbing Procedures8.1.9 A false crotch and/or false-crotch redirect may be used at the discretion of the arborist in lieu of a natural crotch.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.1 - Climbing Procedures8.1.10 The climber shall select a tie-in-point/primary suspension point that prevents lateral movement of the climbing line.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.1 - Climbing Procedures8.1.11 When installing the climbing line or false crotch from the ground, it should be positioned in a suitable location along the main stem/leader/lateral limb. The climber shall visually inspect the anchor point for condition from the ground and, if suitable, shall subject it to a load approximately twice the weight of the climber before climbing commences.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.1 - Climbing Procedures8.1.12 The tie-in point should be positioned so that the arborist will not be subjected to an uncontrolled pendulum swing.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.1 - Climbing Procedures8.1.13 When an arborist is working at heights greater than one-half the length of the arborist climbing line, a stopper knot shall be tied in the end of the arborist climbing line to prevent pulling the line through the climbing hitch.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.1 - Climbing Procedures8.1.14 Arborists working from a stem or spar without a suitable natural crotch shall select tie-in points or a tie-in method that positively prevents the climbing line from sliding down or up or off the stem during climbing operations. Placing a climbing line around a stem in an area without a lateral limb is not acceptable unless the climbing line is cinched or choked around the stem or runs through a double wrapped or adjustable false crotch, which is secured/cinched around the stem. The tie-in point selected shall be able to withstand the forces being applied during the pruning/removal operation.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.1 - Climbing Procedures8.1.15 If a climbing line is damaged in the course of operations, the arborist shall secure himself/herself with a work-positioning lanyard and immediately replace the damaged line.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.1 - Climbing Procedures8.1.16 The ground crew shall keep the climbing line free of debris and obstructions, protect it from damage, and report any damage to the arborist.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.1 - Climbing Procedures8.1.17 The arborist shall check his/her climbing line beneath the climbing hitch for damage while descending.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.2 - Ropes and Arborist Equipment8.2.1 Climbing lines used in a split-tail system and split-tails shall be terminated with an eye splice or a knot that interfaces appropriately with the connecting link. When using a carabiner without a captive eye, the termination selected shall maintain loading along the major axis. The connection between carabiners and terminated rope ends shall be compatible to limit the possibility of accidental disconnection or minor axis loading of carabiners.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.2 - Ropes and Arborist Equipment8.2.2 The arborist shall assure that arborist saddles and climbing gaffs/spurs comply with an appropriate governing standard, and shall be marked accordingly on the product, when new (e.g., arborist saddles marked ASTM F887 if manufactured after 1/1/2018).tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.2 - Ropes and Arborist Equipment8.2.3 Arborist saddles and work-positioning lanyards shall not be altered in a manner that would compromise the integrity of the equipment.tree climbingZ133
ANSI Z133 Arborist Safety Requirements8 TREE CLIMBING8.2 - Ropes and Arborist Equipment8.2.4 Arborist climbing lines used for moving rope systems shall have a minimum diameter of 1/2 inch (12.7 mm) and be constructed from a synthetic fiber, with a minimum breaking strength of 5,400 pounds (24.02 kilonewtons [kN]) without terminations when new. Maximum working elongation shall not exceed 7 percent at a load of 540 pounds (2.402 kN). Arborist climbing lines shall be identified by the manufacturer as suitable for tree climbing.
EXCEPTION to 8.2.4: In arboricultural operations not subject to regulations that supersede Z133, a line of not less than 7/16 inch (11 mm) diameter may be used, provided the employer can demonstrate it does not create a safety hazard for the arborist and the arborist has been instructed in its use. The line selected shall meet or exceed the standards for arborist climbing lines and shall be identified by the manufacturer as suitable for tree climbing.
tree climbingZ133